// Copyright 2023 The BoringSSL Authors
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//     https://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.

#ifndef OPENSSL_HEADER_CRYPTO_FIPSMODULE_KECCAK_INTERNAL_H
#define OPENSSL_HEADER_CRYPTO_FIPSMODULE_KECCAK_INTERNAL_H

#include <openssl/base.h>


BSSL_NAMESPACE_BEGIN

enum boringssl_keccak_config_t : int32_t {
  boringssl_sha3_256,
  boringssl_sha3_512,
  boringssl_shake128,
  boringssl_shake256,
};

enum boringssl_keccak_phase_t : int32_t {
  boringssl_keccak_phase_absorb,
  boringssl_keccak_phase_squeeze,
};

struct BORINGSSL_keccak_st {
  // Note: the state with 64-bit integers comes first so that the size of this
  // struct is easy to compute on all architectures without padding surprises
  // due to alignment.
  uint64_t state[25];
  enum boringssl_keccak_config_t config;
  enum boringssl_keccak_phase_t phase;
  size_t required_out_len;
  size_t rate_bytes;
  size_t absorb_offset;
  size_t squeeze_offset;
};

// BORINGSSL_keccak hashes |in_len| bytes from |in| and writes |out_len| bytes
// of output to |out|. If the |config| specifies a fixed-output function, like
// SHA3-256, then |out_len| must be the correct length for that function.
OPENSSL_EXPORT void BORINGSSL_keccak(uint8_t *out, size_t out_len,
                                     const uint8_t *in, size_t in_len,
                                     enum boringssl_keccak_config_t config);

// BORINGSSL_keccak_init prepares |ctx| for absorbing. If the |config| specifies
// a fixed-output function, like SHA3-256, then the output must be squeezed in a
// single call to |BORINGSSL_keccak_squeeze|. In that case, it is recommended to
// use |BORINGSSL_keccak| if the input can be absorbed in a single call.
OPENSSL_EXPORT void BORINGSSL_keccak_init(
    struct BORINGSSL_keccak_st *ctx, enum boringssl_keccak_config_t config);

// BORINGSSL_keccak_absorb absorbs |in_len| bytes from |in|.
OPENSSL_EXPORT void BORINGSSL_keccak_absorb(struct BORINGSSL_keccak_st *ctx,
                                            const uint8_t *in, size_t in_len);

// BORINGSSL_keccak_squeeze writes |out_len| bytes to |out| from |ctx|. If the
// configuration previously passed in |BORINGSSL_keccak_init| specifies a
// fixed-output function, then a single call to |BORINGSSL_keccak_squeeze| is
// allowed, where |out_len| must be the correct length for that function.
OPENSSL_EXPORT void BORINGSSL_keccak_squeeze(struct BORINGSSL_keccak_st *ctx,
                                             uint8_t *out, size_t out_len);

#if defined(__has_attribute)
#if __has_attribute(vector_size)
#define HAVE_KECCAK_X2
#endif  // vector_size
#endif  // __has_attribute

#if defined(HAVE_KECCAK_X2)
// BORINGSSL_keccak_squeeze_x2 performs BORINGSSL_keccak_squeeze in parallel
// with two same-length outputs. The contexts must be in equivalent state (i.e.
// same config, same amount of bytes absorbed and squeezed).
OPENSSL_EXPORT void BORINGSSL_keccak_squeeze_x2(
    struct BORINGSSL_keccak_st ctx[2], uint8_t *outs[2], size_t out_len);

// BORINGSSL_keccak_short_x2 performs BORINGSSL_keccak in parallel on two
// same-length strings with same-length outputs. |in_len| must be less than 72
// (or actually |rate_bytes|).
OPENSSL_EXPORT void BORINGSSL_keccak_short_x2(
    uint8_t *outs[2], size_t out_len, const uint8_t *ins[2], size_t in_len,
    enum boringssl_keccak_config_t config);
#endif

BSSL_NAMESPACE_END

#endif  // OPENSSL_HEADER_CRYPTO_FIPSMODULE_KECCAK_INTERNAL_H